CDROM-Guide forums

Go Back   CDROM-Guide forums > Main Forums > Video Game Backup - PS2
FAQ Calendar Mark Forums Read
Open   CSec   Data   DevDrv   CoOp   Audio   CDRW   CDG   VCD   DVD   HD DVD   Mac   VGB   PS2   DC   Xbox  


 
 
Thread Tools Display Modes
  #7  
Old Dec 04, 2006, 04:32 PM
silentblackhat silentblackhat is offline
Newbie
 
Join Date: Dec 2006
Location: Portland WA
Posts: 8
Default

sponsored links

 
do u have any soldering tips? i had a hard time soldering before on my xbox because i didnt use flux. it owrked but it was kinda hard. what i understand is that u put a little flux on the end of the wire with a ball of solder on the end of the solder iron...then touch the wire end to the end of the sodlering iron where hte ball of solder so u get the solder on the end of the wire...then for the pads on the motherboard u clean it off with a solvent, put some flux on the pad with a toothpick and then touch the soldered end of the wire to the pad and heat it up so it melts to the pad on the board, correct?

also what type of solder should i use?

Last edited by silentblackhat; Dec 04, 2006 at 05:16 PM.
  #8  
Old Dec 04, 2006, 05:43 PM
4SKIN 4SKIN is offline
Senior Member
 
Join Date: Mar 2005
Location: tim-buck-2
Posts: 410
Default

if you have modded xbox's before,it shouldnt be a problem tbh
if your not sure,then dont attempt it,as one wrong move might render the board uselss
practice on a old board,maybe on a old pc board if you have one

check here for a few tips and hints

***********.chipzone.com/installation/soldertips.cfm
  #9  
Old Dec 17, 2006, 04:21 AM
bud bud is offline
Member
 
Join Date: Oct 2000
Location: U.K.
Posts: 154
Default solderig

--------------------------------------------------------------------------------

Yep....
you're right to tin the tiny wires you are going to attach and ALSO YOU NEED TO TIN THE POINTS ON THE BOARD YOU ARE GOING TO ATTATCH THE WIRES TO!!!!!
The flux assists the solder to adhere to the wire so you get a good connection.
You need a solder which has 95% tin and 5% silver as opposed to 99% tin.
This is because with a higher silver content, the melting point of the solder is lower and so you don't need as much heat applied to melt the solder onto the board.
Too much heat and you can damage electronic components or cause the tracks to lift off the PCB.
You should also invest in a reel of DE-SOLDERING BRAID.....invaluable for correcting mistakes of too much solder. Look it up on the net.
Get a flux pen also and a 15 Watt soldering iron.
You can buy them all from maplins electronics and set yourself up for about 30.
Get some practice and you'll soon get your money back by chipping your friends for them

With both the wire and the contact point on the board tinned oyu can make the joint by touching the tinned wire onto the tinned soldering point and offer the soldering iron up to them. You don't need to leave the iron here long before the solder melts....when you quickly then retract the soldering iron and allow to joint to cool and solidify.
Practice 1st on an old PCB before you attack you're pS2.
Take your time.....and good luck.
If you make a right B----cks of it you can always get a replacement machine from SONY for about sixty quid trading in your damaged PS2!!!
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Problem with Hotmail and IE6 buscuitboy Windows XP 2 Sep 22, 2006 04:10 PM
What modchip options are there for the soldering impaired? Golden_V Video Game Backup - PS2 2 May 26, 2003 10:22 PM
The first ALL ps2 model compatible non-swap modchip evangel Video Game Backup - PS2 4 Sep 16, 2002 10:51 AM
Xbox Modchip Lives SBeck24Svn Video Game Backup - Xbox 2 Jul 06, 2002 04:04 PM
Edited Upuro modchip faq...lets get things straight ! Channel Tech Video Game Backup - PS2 10 May 06, 2002 11:09 AM


All times are GMT -5. The time now is 10:15 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright 1996-2009 CDROM-Guide.com. All rights reserved