CDROM-Guide forums

Go Back   CDROM-Guide forums > Main Forums > Video Game Backup - Xbox
FAQ Calendar Mark Forums Read
Open   CSec   Data   DevDrv   CoOp   Audio   CDRW   CDG   VCD   DVD   HD DVD   Mac   VGB   PS2   DC   Xbox  

Thread Tools Display Modes
Old May 16, 2003, 10:40 AM
Jago6 Jago6 is offline
Senior Member
Join Date: Sep 2000
Posts: 295
Default flash mod without programmer.html

sponsored links
How to flash the eXcuter2 /Matrix MOD chip without A Programmer.

1st. & foremost I would like to thank my friends for this help. Ok now I hold no responsibility if you should damage your xbox & or Mod Chip. Now with that out of the way, lets get started. These you must already have in order to do this.

1.A Xbox Duh.
2.A Mod chip (eXcuter2-Pro/Lite ). Duh duH
3.The bin file that you would like to flash with the chip.
4.Make sure you have the bin either on Cdrom or Hard drive that your going to use.
5.I used evolution X bios flash to do this with.

Well, let's say that you have a xbox already modded (if not acquired 1) with the x2-lite/pro Or Matrix. Now, pay very close attention. Power off & unplug your XBOX. Remove the cover; unscrew the HD & DVD drive. DO NOT disconnect the DVD & Hard drive, just move them out of the way so that you can have access to the MOD. From this point, if you have on off switches to the mods leave the mod on an active for the moment. Ok, Power up your xbox. Make sure it can boot in its' current state. If so, you're good up to this point. If not you need to check all your connections & make sure nothing is shorted or grounded out, remember your xbox is open & on so be careful. This applies to the x2/lite-pro; your xbox should be on the evolutionx screen. Now switch the chip to off or pull the jumper. Carefully unplug the mod from the xbox (cables/ pin header/ pogo pin). Take another mod (the 1 that you're going 2 flash), & put in place of your original mod. Please note that you must 1st make sure that the mod is switched off (disabled) & that the bios flash is switched on (enabled). With the new or blank mod plugged into the xbox, switch the mod to the on (enabled) position & bios flashed enabled. Your xbox should still be on & running @ the evolutionX screen. Ok, goto your util menu on evox to the flash bios menu & select your bin, flash your MOD & you're done. I've flashed several mods that way with no problems. All without a programmer. I havent tried the Matrix mod yet, but I will soon. Have fun.

U can learn something from everybody .
Old May 16, 2003, 11:23 AM
DBZ Racer DBZ Racer is offline
Join Date: Jun 2001
Location: USA
Posts: 100

These are the same steps one can take if you had a bad bios flash on your chip and need to reflash and recover...

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
bad mod install (not by me), will gamesave exploit / tsop flash still work? TheCheekyMonkey Xbox Modchip Help & Installation 3 Oct 23, 2003 06:43 PM
which mod chip is able to flash the tsop on the xbox superman69 Xbox Modchip Help & Installation 2 Mar 12, 2003 02:58 AM
i have a mod and if flash my xbox with EvolutionX V2.2 bios do i still need a mod robertgoodwin Xbox Modchip Help & Installation 6 Jul 22, 2002 11:13 AM
BIOS flash mod for x-box voicon Video Game Backup - Xbox 6 Jun 11, 2002 04:29 PM
Flash Mod chips redwolf Video Game Backup - Xbox 5 May 29, 2002 03:58 AM

All times are GMT -5. The time now is 03:09 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright © 1996-2009 All rights reserved